Redhat配置nagios-安裝nagios-plugins
作者：wonitazansa1
Redhat配置nagios：Nagios是監控系統，Nagios能監控所指定的本地或遠程主機以及服務，同時提供異常通知功能等。這篇文章講述的是安裝nagios-plugins
安裝nagios-plugins
本文講述的是：Redhat配置nagios。返回大綱。
- [root@localhost src]# tar zxvf nagios-plugins-1.4.15.tar.gz
- [root@localhost nagios-plugins-1.4.15]#./configure --with-nagios-user=nagios --with-nagios-group=nagios --prefix=/usr/local/nagios
- [root@localhost nagios-plugins-1.4.15]# make && make install
驗證是否安裝成功，是否生成如下文件
- [root@localhost nagios-plugins-1.4.15]# ls /usr/local/nagios/libexec
- check_apt check_disk_smb check_ide_smart check_mrtg check_nwstat check_sensors check_users
- check_breeze check_dns check_ifoperstatus check_mrtgtraf check_oracle check_smtp check_wave
- check_by_ssh check_dummy check_ifstatus check_nagios check_overcr check_ssh negate
- check_clamd check_file_age check_imap check_nntp check_ping check_swap urlize
- check_cluster check_flexlm check_ircd check_nt check_pop check_tcp utils.pm
- check_dhcp check_ftp check_load check_ntp check_procs check_time utils.sh
- check_dig check_http check_log check_ntp_peer check_real check_udp
- check_disk check_icmp check_mailq check_ntp_time check_rpc check_ups
配置nagios的WEB接口，也可以通過如下命令更改用戶密碼，
- [root@localhost etc]# /usr/bin/htpasswd -c /usr/local/nagios/etc/htpasswd nagiosadmin
- New password:
- Re-type new password:
- Adding password for user nagiosadmin
- [root@localhost etc]# service httpd start
- Starting httpd: [ OK ]
編輯httpd.conf，在結尾加上如下內容，保存，啟動apache，service httpd restart
- ScriptAlias /nagios/cgi-bin /usr/local/nagios/sbin
- Options ExecCGI
- AllowOverride None
- Order allow,deny
- Allow from all
- AuthName "Nagios Access"
- AuthType Basic
- AuthUserFile /usr/local/nagios/etc/htpasswd
- Require valid-user
- Alias /nagios /usr/local/nagios/share
- Options None
- AllowOverride None
- Order allow,deny
- Allow from all
- AuthName "Nagios Access"
- AuthType Basic
- AuthUserFile /usr/local/nagios/etc/htpasswd
- Require valid-user
設置開機啟動nagios服務
- [root@localhost nagios-plugins-1.4.15]# chkconfig --add nagios
- [root@localhost nagios-plugins-1.4.15]# chkconfig nagios on
驗證nagios配置是否正常，此命令以后會經常使用，warning和error為0，表示正常，后面不正常的討論，這里可以啟動nagios服務
- [root@localhost nagios-plugins-1.4.15]# /usr/local/nagios/bin/nagios -v /usr/local/nagios/etc/nagios.cfg
- ……
- Checking misc settings...
- Total Warnings: 0
- Total Errors: 0
- [root@localhost nagios-plugins-1.4.15]# service nagios start
- Starting nagios: done.
【編輯推薦】
責任編輯：zhaolei
來源：
csdn
